Stamp Machines

Product Details:

The raw material used for making the stamp :

• Photo Polymer Resin
• Border Tap
• Subtract Sheet
• Mounts
• Cover Film Roll
• Hardner
• Washing Solutions
• Foam Tape

Product Details:

We design and manufacture a quality range of Flash stamp Machine that is as per international standards. These Flash Stamp Machines are designed with high quality flash tube.

The raw material used for making the Flash stamp :

• OHP Sheet
• Flash Foam
• Ink
• Mount
• Adhesive

Product Details:

We design and manufacture a quality range of Flash stamp Machine that is as per international standards. These Flash Stamp Machines are designed with high quality flash tube.

The raw material used for making the Flash stamp :

• OHP Sheet
• Flash Foam
• Ink
• Mount
• Adhesive

Product Details:

We design and manufacture a quality range of Flash stamp Machine that is as per international standards. These Flash Stamp Machines are designed with high quality flash tube.

The raw material used for making the Flash stamp :

• OHP Sheet
• Flash Foam
• Ink
• Mount
• Adhesive

Additional Information:

• Packaging Details: corrugated box

Product Details:

The raw material used for making the stamp :

• Photo Polymer Resin
• Border Tap
• Subtract Sheet
• Mounts
• Cover Film Roll
• Hardner
• Washing Solutions
• Foam Tape

Additional Information:

• Production Capacity: 100 stamps

Product Details:

We design and manufacture a quality range of Flash stamp Machine that is as per international standards. These Flash Stamp Machines are designed with high quality flash tube.

The raw material used for making the Flash stamp :

• OHP Sheet
• Flash Foam
• Ink
• Mount
• Adhesive

Product Details:

• Co2 Laser cutting machine offers a wide variety of cutting and engraving options on different types of materials like acrylic, leather, wood, fabric ,plasticetc with high speed and accuracy. Cutting and engraving through laser is a non-contact process which makes the running and maintaining procedure quite easy. With a mere setting of power a single machine can perform both the cutting and engraving functions at the same time. Here, we can provide you with single head and double head machines depending upon your requirement of production.

• This single head laser cutting machine is a perfect solution for cutting and engraving all types of acrylics,leather,mdf,plastics,fabric, rubber,plexi glass etc. with high precision and quality. With the best quality products used in its production, it has 5 models, each with a different work area giving you the satisfactory results in low cost and low maintainence.

• Visible red dot pointer – Red light positioning device indicates the location of laser head and eliminate the trouble about manual positioning.
• Air assist – with air assist, you can remove the combustible heat and gasses from the cutting surface, thus you will have a better cutting quality.
• LCD panel – Crystal display for the friendly interface and make the operation more convenient and flexible to use.
• Top quality optics – Imported silicon reflectors with a wavelength of 10.6 micrometre and diameter 25.4mm to give better efficiency.
• Motion control system – The laser controllers, RD 4.23 allow the system to work faster and have a much better cutting and engraving quality.
• High quality and long life laser tube.
• Imported japanese bearings and guide rails for precise movement of laser head.
• Honeycomb design work table to give better vaccum to hold the material.
• Water protection – This feature protects the laser tube when the water cooling system is not working.
• Pass through door design – This design feature helps to cut the long materials which longer than the machine itself.
• Closed loop chiller (100 W and greater) – Click here for technical specifications of chillar.
• Smart carver controller – This high-tech controller is based on 32 bit DSP technology to get the improved performance.
• 32M (or higher) mass memory unit – this feature simultaneously saves many work data and does not loose the closed down document which makes the batch work easy.
• USB data interface.
• Power Supply 80 watts.
• Laser software – Uses is a professional software that controls the system settings. It has plug-in for AutoCAD, CorelDraw and photoshop.
• Triple exhaust system – Exhaust the smoke/fume roundly.
• Laser tool kit.